Book a Table

Windsor, Oct 12th 2023

Book a Table

Exhibitor Table Registration is now CLOSED

Contact

GREG PALIOURAS
Show Manager
Publisher, Shop Metalworking Technology

Shop Metalworking Technology Expo is a closed show for qualified delegates only.
Show management reserves the right to decline registration.

Request a callback

Please fill out the form below and we will call you back.

CONTRACT

This application shall upon written acceptance by SMT Expo, the Show Manager, confirm the applicant’s commitment to exhibit at the Ciociaro Club on October 12, 2023. Furthermore, upon acceptance of this contract, the rules and regulations that follow and the rules and regulations issue as part of the Exhibitor’s Information Kit become binding upon both parties to the agreement.

SPACE ASSIGNMENT
Management reserves the right to make final space assignment after the acceptance of the application, should it be necessary in the best interest of the Exhibition.

PAYMENT
Applications for space must be accompanied by full payment per table booked. Full payment must be made immediately in order to secure space in the show. Exhibitors failing to pay by due date forfeit their right to exhibit. Payments should be made to 

Verdi Business Media, Inc.
PO Box 62073 North York RPO Victoria Terrace
North York, ON   M4A 2W1

CANCELLATION
In the event that an Exhibitor cancels in writing from the show, the following conditions shall apply:
i) Cancellation prior September 11, 2023 | the Exhibitor will forfeit a deposit fee of $500 per show.
ii) Cancellation September 12, 2023 | the Exhibitor will forfeit the entire space cost.
iii) Show Management reserves the right to cancel space should payment not be received from the Exhibitor within prescribed time limits.
iv) If the Show Management is prevented from holding the Show or cannot permit an Exhibitor to occupy the Exhibitors rented space due to circumstances beyond management’s control including, but not limited to, strike, re, health-related issues, civil disobedience, inclement weather, lockout, bankruptcy, Acts of God, pandemic, facility unavailability for whatsoever cause: Show Management will refund to the exhibitor the amount of rental paid by him, less a proportionate share in relation to the other exhibition space, of the total Show expenses incurred by Show Management to that date, and Show Management shall have no further liability to the Exhibitor.

NOTE: All cancellations must be made in writing and will take effect upon date of receipt at the Show Manager’s offices.

ADMINISTRATIVE FEES
Any exhibit fees paid that are changed back or where the financial transaction is cancelled by the bank or credit card will be subject to a minimum administrative fee of $50CAD or the cost of the chargeback, whichever fee is greater.

LOSS OR DAMAGE
Exhibitor will be liable for and will indemnify and hold harmless management from any loss or damages whatsoever occurring to or suffered by any person or company including, without limiting the generality of the foregoing, Exhibitor, other Exhibitors, management contractors, the owner of the building and their respective agents, servants, and employees and members of the public attending the show either (a) on the said space or (b) elsewhere during show set-up, take-down or during actual show hours or anytime on the premises. Neither the facility owners nor the Show
Management will be responsible for loss or damage to persons’ exhibits or decorations by fire, accident, theft, or any other cause while in the exhibition buildings or during transport to a show, between shows or returning from a show.

INSURANCE/COMPLIANCE
Exhibitor is required to submit certificate of insurance prior to show naming Verdi Business Media as additional insured. The Exhibitor assumes all responsibility for compliance with all pertinent ordinances, regulations and codes of duly authorized local, Provincial and Federal governing bodies concerning safety, health together with the rules and regulations of the operators and/or owners of the property wherein the Show is held.

USE OF EXHIBIT SPACE
Exhibitors shall reflect their company’s highest standard of professionalism while maintaining the table during the Show hours. The booth must be maintained by at least one company representative at all times during the Show’s operation. All demonstrations and exhibits must be contained to the contracted space (8’ wide x 5’ deep). In keeping with the philosophy of holding costs to a minimum, the regulation limiting exhibits to a maximum height of eight feet (8’) will be enforced. Booth-type exhibits will not be allowed. Booth takedown may not occur until the announced show closing.

SHOW MANAGEMENT
All inquiries pertaining to the Show should be directed to:

Verdi Business Media, Inc.
PO Box 62073 North York RPO Victoria Terrace
North York, ON   M4A 2W1
Tel: (416) 701-9322

Email: [email protected]

Shop Metalworking Technology Expo is a closed show for qualified delegates only.

Show management reserves the right to decline registration.

Past Exhibitors

  • APMA (Automotive & Aircraft Parts Manufacturers’ Association Canada)
  • Acetronic
  • Allied Machine & Engineering
  • Automate Canada
  • Belmont Equipment & Technologies
  • Blaser Swisslube Inc.
  • CAM-TOOL by CGS North America Inc.
  • CAMM (Canadian Association of Moldmakers)
  • CIMCOOL Canada
  • CTMA (Canadian Tooling & Machining Association)
  • Capital North Corporation
  • Colonial Tool Group Inc.
  • Corwhin Tool & Manufacturing Ltd.
  • DME Company
  • DMG MORI Canada Inc.
  • DSI Manufacturing Ulc
  • DiPaolo Machine Tools Ltd.
  • EMEC Machine Tools Inc.
  • Elliott Matsuura Canada Inc.
  • Expertech Distribution and Technologies Inc.
  • FCS North America Inc.
  • FPT Industrie S.P.A.
  • Ferro Technique
  • Fooke USA Inc.
  • Haimer-USA, LLC
  • High Speed Machinery
  • Technologies Canada Inc.
  • Iscar Tools Inc.
  • LSI Supply Inc.
  • Longterm Technology Services Inc.
  • MAPAL Inc.
  • MC Machinery Systems Inc.
  • MEGATEL
  • Mag Tool
  • Master Fluid Solutions
  • Mastip Hot Runner Systems
  • Mazak Canada
  • Moon Machinery Inc.
  • NCPerformance Technology Inc.
  • Natex Machinery Group Inc.
  • OSG CANADA, LTD.
  • OnRamp Solutions Inc.
  • Optimoule
  • PCS Company
  • POM Solutions Inc.
  • Performance Machinery LLC
  • Progressive Components
  • Promac North America Corp.
  • Proto3000
  • REGO-FIX Tool Corp.
  • Ramstar Carbide Tool Inc.
  • Renishaw (Canada)
  • Romquest Technology
    SME (American Society of Tool Engineers)
  • Sandvik Coromant Canada
  • SolidCAD
  • Sputtek Inc.
  • TOS America Inc.
  • TSquared Tooling Solutions
  • Tool & Cutter Supply Co. Ltd.
  • Triumph Tool Ltd.
  • Universal Robots USA, Inc.
  • hyperNC Solutions Inc.
  • iD Additives